Replacing uPVC Window Handles
The replacement of window handles made of upvc is a simple job. It is important to make sure that the new handle is a good fit for the spindle that was cut out of the window mechanism.
If you follow the steps below, any cockspur handle will fit most windows. The step height of the handle is key.
What to Look for
Over time, uPVC handles on many windows in the UK can start to show signs wear and wear and tear. The handle of the window may become shaky or difficult to operate when this occurs. This is a easy task that can be completed by anyone who is familiar with basic hand tools.
The first step is to ensure that the handle is firmly fixed to the window frame and in a position that is open. The next step is to locate the fixing screws or pins that hold the handle in the position it is in. These are usually located on the inside of the handle. They can be removed using the screwdriver and pliers.
Once the handle is loose it can be taken from its hinges by gently pulling it off. It is then time to find a new handle of the same style and size. This can be done at the DIY store or on the internet. The process should take only five minutes, and you will need a screwdriver is all you need.
One important factor to consider when replacing the uPVC window handle is the step height. This is the distance from the base of the handle to where it rests on the window frame. This is a standard measurement and you should confirm the height of the step before purchasing an replacement handle.
There are various sizes depending on the kind of handle. Inline handles can be found for uPVC window with centers of 31mm for lugs, while cockspur handles come with centers of lugs of 43 millimetres. Tilt-and-turn handles are common on uPVC windows. They have a specific design that allows the window to be tilted to allow for ventilation, and then turned to fully open the window.
The most frequent breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This can make them hard to open and therefore it is crucial to ensure that any replacement handle you buy has the same length of spindle as your existing one.
Remove the old Handle
Incorrectly fitted or damaged window handles can cause your double-glazed windows to open or close incorrectly, and can result in them becoming stuck. This could be due to various reasons, including general wear and tear on the metal handle or corrosion. In these cases, it is vital to replace the window handle as promptly as you can to avoid further damage or loss of functionality.
One of the first steps that you should do when replacing window handles made of upvc is to remove the old handle from the window. Begin by removing upvc door handle repairmywindowsanddoors.co.uk by the handle while it is in the closed position. Once you have removed that screw, you can take off the handle. You can make the process easier by using an electronic screwdriver.
It is also important to note that the screws on the handle could be hidden behind caps made of plastic, so it is a good idea to use an Stanley knife to the screw caps and then take them off. After removing the handle, you will have to examine the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is crucial as you'll need to measure the length of the spindle on the old handle to make sure it is in line with the size of the window mechanism and handle spindle that has been cut out.
The different kinds of window handles made from upvc include: Espag handles, which are equipped with a central screw and can be turned left or right; Cranked handles, which have two screws and are used on tilt and turn upvc windows as well as Spade handles, which have an arm with a flat surface and can be used on either side of the window. Once you have found a suitable replacement, it's just a matter of screwing the handle into place and making sure that the spindle is inserted into the lock mechanism. After that then it is time to secure it to the window frame and your replacement window handles made of upvc must be secure.
Measure the Spindle
If you need to replace a handle made of upvc that has fallen, it's likely the spindle holding it in place is damaged or is loose. In certain situations it is possible to tighten the spindle with pins or screws. In some instances it is necessary to replace the handle. There are several kinds of window handles made of upvc. These include inline espagnolette handles as well as cockspur handles. tilt and turn handles. Each type has a different method for installing and removing the handle.
Before you purchase a new handle, it is important to know the dimensions of the one you have. This will ensure that the handle will fit the window in a proper manner and will be the right size. All handles are sized in accordance with industry standards, making it easy to determine the right size.
To measure the size of your handle, first, take it out of the window by turning it to an open position. You should be able to determine the size of the screw or pin that secures the handle. Use a ruler or tape measure to determine the length the spindle is. Once you know the length of the spindle you can purchase a new one with exactly the same size.
When purchasing a replacement you should be aware of the step height of the upvc window handle. The step height is measured from the base to the point where the handle is positioned on the frame. Typically, this will be approximately 21mm for uPVC windows or 9mm for aluminum. Dropping something in the gap will allow you to see how far the handle extends before it meets an obstruction.
Cockspur handles usually have different backset heights based on the type of window they are installed in. Inline Espag handle heights are 43mm from centre to centre (two fixing points). Cockspur handles have different backsets based on the type of window they are located in. This is due to the fact that they have a spur which extends from their handle and is locked onto a cockspur wedge-striking plate.
Install the new handle
After you've chosen the new handle, ensure that it is aligned with the screw holes on the door. Then, secure it with the screws provided. Install the latch lever the same way as the handle that you are replacing when you're replacing the door handle. After that, attach the door trim in order to conceal the screws for mounting and finish the job.
Tips: To remove the metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the floor. Then, use an hammer and tap the narrow end. Be careful not to scratch the handle or the handle spindle.